ADC Blood Pressure Monitor 6014 User Manual

Electronic  
Blood Pressure  
Printer  
11. HOW TO CONTACT US  
Detailed user information about our products  
as well as services can be found at:  
TM  
For use with ADvantage Advanced Automatic  
Blood Pressure Monitors; Models 6014 and 6016.  
6014P  
Instruction Manual  
PLEASE NOTE:  
THIS MEDICAL INSTRUMENT MUST BE  
USED ACCORDING TO INSTRUCTIONS  
TO ENSURE ACCURATE READINGS.  
American Diagnostic Corporation  
55 Commerce Drive, Hauppauge, New York 11788  
Telephone: 631-273-9600  
®
Fax: 631-273-9659  
Questions?  
®
Call ADC toll free at 1-800-232-2670  
1-800-232-2670  
American Diagnostic Corp.  
IB p/n #93-6014P-00 - rev 1  
 
Malfunction  
Remedy  
1. INTRODUCTION  
The LED remains flashing while  
the printer is switched on  
although the batteries are  
good.  
1. Check whether the batteries are installed with  
the correct polarity.  
2. If the LED is unusually flashing, remove the  
batteries and re-install them or exchange them  
for new ones.  
The diagnostic printer 6014P is a compact unit for ADC® AdvantageTM Advanced  
Automatic Blood Pressure Monitors. The enhanced printer covers both character and  
graphic print. High-reliability and high-quality print is assured due to the ultra simple  
design and practicability. Key features include:  
Compact and lightweight design  
High-quality components  
Battery-powered operation  
Designed for versatile applications  
Simple mechanism ensures high-reliability  
1. Check whether the cable is connected with the  
monitor and printer.  
2. Examine whether the paper is positioned properly  
and is ready for printing.  
Press the PRINT button on  
the monitor, but nothing prints  
1. Examine whether the paper is positioned properly.  
2. Check if the paper roll has been exhausted and  
needs to be replaced by a new one.  
There’s no response for paper  
feeding  
2. PRINTER PARTS  
a) Front View  
Top Cover  
Bottom Cover  
Paper Cutter  
7. CARE AND MAINTENANCE  
a) Do not expose the device to  
extreme temperatures, humidity,  
dust, or direct sunlight.  
Paper  
Feed  
Paper Roll  
LED  
ON/OFF Switch  
b) Clean the device with a soft, dry  
cloth. Do not use gasoline, thin-  
ners, or similar solvent.  
b) Back View  
c) Do not drop the device or treat it  
roughly in any way. Avoid strong  
vibrations.  
Printer port socket  
AC/DC adapter socket  
(AC/DC adapter sold separately)  
d) Never open the device!  
The manufacturer warranty is  
invalid once the device is opened.  
9
2
 
3. SETTING UP THE PRINTER  
5.1. How to Print a Chart and all Readings  
a) Connect the printer to the monitor and switch the printer ON.  
b) Press the PRINTER button of the monitor and hold it for at least 3 seconds. The  
display will change from “Pr1” followed by “Pr2”. Release the PRINTER button and the  
printer will print all stored measurements with a corresponding chart.  
3.1. Inserting the Batteries  
The battery compartment is located on the  
underside of the device (See illustration).  
a) Remove cover as illustrated.  
b) Insert the batteries (4 x size “AA”),  
thereby observing the indicated polarity.  
c) If the green LED starts flashing, the batteries  
are discharged and must be replaced.  
___  
________  
NAME:____  
Pr2  
Optional  
__  
________  
BIR  
TH:_____  
00:09  
--------  
DATE TIM  
AM  
5
JAN•01•200  
Date & Time  
Systolic, Diastolic, and  
Pulse Readings  
--------  
E
S
D
P
01. JAN-01-09:00AM  
Attention!  
130  
81  
89  
61  
02. JAN-02-09:01AM  
103  
03. JAN-03-09:00AM  
113  
04. JAN-04-09:00AM  
124  
05. JAN-05-09:00AM  
If the green LED starts flashing,  
the device will not function until the  
batteries have been replaced.  
Use 'AA' Long-Life or Alkaline 1.5V  
Batteries. Do not use rechargeable  
batteries.  
If the printer is left unused for long  
periods, remove the batteries from  
the device.  
71  
81  
80  
90  
76  
89  
87  
114 101  
130 81  
79  
84  
102  
71  
96  
69  
76  
89  
137  
05. JAN-06-09:00AM  
114  
06. JAN-07-09:00AM  
129  
07. JAN-08-09:00AM  
112  
08. JAN-09-09:00AM  
09. JAN-10-09:00AM  
Average Reading  
0-83-78  
MEAN: 12  
37  
: 103--1  
: 71--101  
61--102  
S
D
P
RANGE  
RANGE  
RANGE:  
LED flashing  
------  
--------  
C
---------  
S=SYSTOLI  
mmHg  
Hg  
LIC  
mm  
BEAT/MIN  
D=DIASTO  
P=PULSE  
A=AVERAGE  
R=ARRHYTH  
MIA  
200  
0
15  
0
10  
50  
Reading Sequence  
Bar Graph  
lic  
sto  
130  
103  
3
11  
124  
13  
11  
Sy  
olic  
ast  
81  
Di  
.
02  
01  
71  
81  
80  
90  
76  
89  
87  
.
.
03  
.
04  
7
4
12  
11  
.
05  
.
06  
9
2
.
07  
.
08  
4
7
11  
1
10  
80  
80  
.
.
11  
09  
10  
12  
11  
9
.
0
20  
0
15  
0
0
1
50  
6. TROUBLESHOOTING  
If problems occur when using the printer, the following points should be checked and  
if necessary, the corresponding remedies taken:  
3
8
 
4.6. Cutting Paper  
3.2. Using an AC Adapter  
Once you finish the printing job, check the paper to  
see if it is easy to tear off.  
It is possible to operate this printer  
through the ADC® AC adapter  
If it is not long enough to tear off, depress the  
PAPER FEED button to lengthen the paper.  
(output 6V DC / 600mA with DIN plug). Make  
certain that you use an AC adapter which ful-  
fills the legal requirements.  
90 °  
Paper cutter  
Note:  
Don’t pull out the paper if you would like to cut it.  
To cut the paper, pull it forward over the paper cutter.  
The paper has to be vertical (90°) with the paper  
cutter; otherwise, the paper will be difficult to tear off.  
The print on the paper does not last forever. It fades  
over time. This is normal for thermal printers such  
a) Plug the DIN plug into the socket at the  
back left of the instrument. (as shown in  
diagram)  
b) Plug the AC adapter into a 110V power  
socket. Test that power is available by  
sliding the 0/I (ON/OFF) switch.  
AC/DC adapter  
socket  
LED dark  
LED bright  
as the ADC® diagnostic printer. The readability lasts longer the less the print is in  
contact with light. If you file the printed paper in a folder, the print will last longer.  
If you would like to store the values forever, we recommend you photocopy them  
or transfer the data to another media.  
Note:  
No power is taken from the batteries while the AC adapter is connected to the  
instrument.  
If the power is interrupted during the measurement (e.g. by removal of the AC  
adapter from the socket), the instrument must be reset by removing the DIN plug  
from its socket.  
5. HOW TO PRINT THE LAST STORED MEASUREMENT (One Reading)  
a) Connect the printer to the monitor and switch the printer ON.  
Consult ADC® if you have questions relating to the AC adapter.  
b) Press the PRINTER button of the monitor once. The display will show “Pr1” and  
the printer will print last stored measurement for the active User (User1 or User 2)  
3.3. Cable Connection  
Insert one end of the cable into the printer  
port socket at the back right of the  
instrument (as shown in the diagram).  
Pr1  
Connect the other end with the blood pres-  
sure monitor (both connectors are identical).  
___  
________  
NAME:____  
Optional  
____  
________  
BIRTH:___  
ODE  
00:0  
9AM  
--------  
AVERAGE M  
05  
JAN•01•20  
--------  
Single or Average Mode,  
Date & Time  
Systolic, Diastolic, and  
Pulse Readings  
Printer port  
socket  
mmHg  
mmHg  
SYS  
DIA  
119  
80  
BEAT/MIN  
PULSE 68  
--------  
-
--------  
7
4
 
3.4. Inserting the Paper Roll  
4. CARRYING OUT A PRINTING OPERATION  
Switch the printer on by sliding the  
I/O (ON/OFF) switch to the left.  
4.1. Power On  
Before powering the printer, check that the batteries  
are inserted properly.  
Lift the top cover by squeezing the sides  
with your fingers and pulling up.  
Push the O/I ON/OFF switch to the left side in order  
to power the printer.  
The green LED will light.  
Insert the ”under” end of paper roll into the slot  
of the internal compartment.  
Push the paper as deep as possible into  
the slot.  
4.2. Paper Feeding  
LED bright  
Before you start the printing operation, check that  
the paper is installed properly in the correct position.  
If it is not, press the PAPER FEED button to feed additional  
paper into the printer.  
Press the PAPER FEED button until paper  
appears at the Paper Cutter.  
Note:  
Put paper roll into the compartment and  
close the lid.  
Press the button once to advance 1 line.  
Continually depressing the button will advance  
multiple lines.  
LED bright  
4.3. Printing  
Paper roll  
Connect the printer with the monitor as explained in Section 3.3.  
Push the print button on the monitor (for details, refer to the manual of  
the related monitor).  
There is only 1 kind of paper roll used in this  
unit. ADC® sells extra paper rolls, contact our  
Customer Service Department for more  
details.  
4.4. Low Voltage Indication  
When the LED is flashing under power-on operation,  
it indicates that new batteries are needed.  
Note:  
When the batteries are replaced the printer will  
operate properly.  
LED flashing  
The paper roll is 1" thick (25mm-standard package) and 38mm wide.  
Note:  
If the printer is connected with an AC adapter, the low voltage indicator  
will not occur.  
If there are problems when inserting the paper, cut the edge so that the corners of  
the paper are square (90°, see below).  
4.5. Power Off  
After you are done printing, push the O/I (ON/OFF) switch  
to the right side in order to turn off the printer.  
The LED will become dark.  
5
6
 

A4 Tech Digital Camera PK 335 User Manual
Adder Technology Music Mixer ALGTX ALGRX User Manual
ADI Systems Marine Radio AT 201 User Manual
ADT Security Services Home Security System 200 Plus User Manual
Aga Ranges Flooring Underfloor Heating User Manual
Aiwa CD Player CSD TD52 User Manual
AKG Acoustics Microphone CS1 User Manual
Alpine CD Player CDE 9843 User Manual
Amana Microwave Oven AMV2175CB User Manual
Axis Communications Security Camera 231D+ User Manual